#1
|
|||
|
|||
TYHJÄKÄYNTIOngelma VM.85 vetten tyhjäkäynti putoaa kuumana välillä niin alas, että auto sammahtaa risteyksissä. Tietokoneenhan pitäisi säätää käynti kulloinkin tilanteen mukaan. Läppärungon kyljessä olevasta kaasuvivun rajoitin ruuvista voi säätää isommalle tyhjäkäyntiä, mutta vaikuttaako se tietokoneen saamaan informaatioon haittaavasti. Sehän on sama kuin painaisi hieman kaasua koko ajan. En tarkoita tässä TPS:n säätöä vaan vain kaasuvivun toppari ruuvin säätöä. Note! This message was posted anonymously!
|
#2
|
|||
|
|||
Missään nimessä sitä toppari ruuvia ei saa ruuvailla.Läppien pitää olla kokonaan kiinni ja IAC-valve (idle air control)säätää tyhmäkäynnin.
Note! This message was posted anonymously! |
#3
|
|||
|
|||
Tässä ohjeet kuinka puhdistaa IAC ja säätää tyhjäkäynti:
How to Service the Idle Air Control (IAC) Background 1. The IAC is used by the ECM to create a controlled air "leak" that establishes the idle speed. 2. Problems with the IAC can result in hunting idle, stalling and poor tip-in. Cleaning/Replacement The IAC pintel and bore should be periodically cleaned to remove carbon from the EGR feedback residues. The IAC bore in the base plate should be cleaned before installing a new IAC assembly (skip steps 3 & 4). 1. Disconnect the cable from the IAC motor. 2. Unscrew the IAC motor from the base using care not to lose the pintel and spring. 3. Remove the IAC gasket and use TB cleaner to clean carbon from the IAC pintel. 4. Clean the IAC pintel bore within the base. Use care not to leave any debris within the bore. 5. Install the pintel and spring back into the IAC motor, if it fell out. 6. Install thegasket onto the IAC motor and screw the assembly back into the base. 7. Install the cable into the IAC connector. Pre-Adjustment Setup 1. Jumper ALDL pins A & B (upper right) together. 2. Turn the ignition key On. 3. Wait 1 minute for the ECM to fully extend the IAC pintel 4. Disconnect the cable from the IAC motor so the pintel will remain extendd. Base Idle Adjustment The base idle adjustment screw is located on the driver side of the TB. 1. Start the engine and set base idle to 450RPM. This is best done by starting at a higher idle and slowly backing down in RPM. 2. Stop the engine, reconnect the cable to the IAC motor and remove the ALDL pins A & B jumper. 3. Restart the engine and verify idle speed control is working properly. NOTE If idle problems persist, replacement of the IAC motor/pintel may be required. -------------- 1988 Corvette |
Käyttäjiä lukemassa tätä viestiketjua: 1 (0 jäsentä and 1 vierasta) | |
|
Samanlaisia viestiketjuja | ||||
Viestiketju | Aloittaja | Foorumi | Vastauksia | Viimeisin viesti |
HJ:n tyhjäkäynti | Kuupo | Tekniikka & Jutustelu | 3 | 31.12.2007 21:01 |
Rangen EFI - tyhjäkäynti | Niko | Tekniikka & Jutustelu | 16 | 24.07.2006 21:17 |
Patrollin tyhjäkäynti? | Repro | Tekniikka & Jutustelu | 5 | 12.04.2006 18:52 |
Läjän tyhjäkäynti | Antsa | Tekniikka & Jutustelu | 5 | 04.04.2006 15:03 |
Tyhjäkäynti | Vuosimallit 1984-1996 | 1 | 06.05.2003 15:04 |