LUBRICATION SPECIFICATIONS
LUBRICATION SPECIFICATIONS TABLE
Application Fluid Specifications
Automatic Transmission ......................... Dexron-IIE ATF
Brake Master Cylinder ......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant .......... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (1)
Gasoline Engine
Temperature Range
Above 30°F(-1°C) ....... SAE 20W-40 Or 20W-50 API SH/CD
Above 0°F (-18°C) ........ SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60°F (16°C) .............. SAE 5W-30 API SH/CD
Diesel Engine
Temperature Range
Above 30°F (-1°C) ................ SAE 15W-40, 20W-40 Or 20W-50 API SH/CD
0°F (-18°C) to 100°F (38°C) ...... SAE 10W-30 API SH/CD
Less Than 50°F (10°C) .............. SAE 5W-30 API SH/CD
Front Axle ................................ SAE 80W-90 API GL-5
Rear Axle ................................. SAE 80W-90 API GL-5
Rear Axle (Trac-Lok) (2) ................. SAE 80W-140 API GL-5
Rear Axle (Trailer Towing) (3) .......... SAE 75W-140 Synthetic
Hydraulic Clutch .............. DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ....................... SAE 75W-90 API GL-5
Manual Steering Box .............. Multi-Purpose NLGI Grade 2EP
Power Steering Pump ...................... Power Steering Fluid
Transfer Case .................................. Dexron-IIE ATF
Brake Caliper Bushings ....... GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins .......... GE 661 or DOW 111 Silicone Grease
Wheel Bearings ............ Multi-Purpose NLGI Grade 2EP, GC-LB
Drive Shaft U-Joints ...... Multi-Purpose NLGI Grade 2EP, GC-LB
Steering Linkage (4)(5) ... Multi-Purpose NLGI Grade 2EP, GC-LB
Ball Joints (4)(6) ........ Multi-Purpose NLGI Grade 2EP, GC-LB
Engine Oil Filter (Diesel) (7) .... AMC/Jeep (P/N 8983 002 656)
Weatherstrip ......................... Silicone Spray Lubricant
(1) - SAE 10W-30 SH/CD is preferred.
(2) - Add 2 Ozs. (59 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must be
DRAINED and FLUSHED with clean mineral based (non-synthetic)
axle lubricant. Then refill with new synthetic lube.
(4) - Use low pressure grease gun to prevent seal damage.
(5) - Fill until lubricant squeezes out from the base of seals.
(6) - Fill ball joint until seal starts to swell.
(7) - Use of AMC/Jeep Oil Filter is RECOMMENDED.
FLUID CAPACITIES
FLUID CAPACITIES TABLE
Application Quantity ( 1)
A/C System R-12 Refrigerant Capacity ............... 36-40 Ozs.
Automatic Transmission
1984-86 (904 HD)
Fluid Change .............................. 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ....................... 8.0 Qts. (7.6L)
1987-88
Fluid Change .............................. 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ....................... 8.5 Qts. (8.0L)
Cooling System (2)
4-Cylinder ................................. 10.0 Qts. (9.5L)
6-Cylinder ................................ 12.0 Qts. (11.4L)
4-Cylinder Turbo Diesel (1985-87) ........... 9.0 Qts. (8.5L)
Engine Oil
4-Cylinder .................................. 4.0 Qts. (3.8L)
6-Cylinder .................................. 6.0 Qts. (5.7L)
4-Cylinder Turbo Diesel (1985-87) ........... 5.5 Qts. (8.5L)
Fuel Tank
Standard ................................. 13.5 Gals. (51.1L)
Optional ................................... 20 Gals. (75.7L)
Manual Transmission (3)
AX4 (AISIN) ................................. 7.4 Pts. (3.5L)
T4 (Borg-Warner) ............................ 3.9 Pts. (1.8L)
AX5 (AISIN) ................................. 7.0 Pts. (3.3L)
T5 (Borg-Warner) ............................ 4.5 Pts. (2.1L)
Transfer Case
1985-86
Selec-Trac (229 Full-Time) ................ 6.0 Pts. (2.8L)
Command-Trac (Part-Time 207) .............. 4.5 Pts. (2.1L)
1987
Selec-Trac ................................ 2.5 Pts. (1.2L)
Command-Trac .............................. 2.2 Pts. (1.0L)
1988
Selec-Trac ................................ 3.0 Pts. (1.4L)
Command-Trac .............................. 2.2 Pts. (1.0L)
Drive Axles (3)
Front ....................................... 2.5 Pts. (1.2L)
Front (Disconnect Housing) (4) ............. 5.0 Ozs. (0.15L)
Rear ........................................ 2.5 Pts. (1.2L)
Rear (Trac-Lok) (5) ......................... 2.5 Pts. (1.2L)
(1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
(2) - Includes 2.3 Qts. for coolant recovery bottle.
(3) - Fill to bottom of filler plug hole.
(4) - Add 5 Ozs. of gear lubricant through indicator switch hole.
(5) - Add 2 Ozs. of Limited-Slip differential lubricant additive
first, then add new fluid.
Tuommosta löyty, kai tästä jotain iloo on, vielä kun sais selville sen, että mikä öljyn suodatin motonetista kannattais ostaa...<img src=icon_smile_wink.gif border=0 align=middle>
--Silkkihanska on paras hanska! Parempaa työkinnasta saa hakea!--
....o_o_o_o
./| ,[_____],
|¯¯¯L--O|||||||O
()_)¯()_) ¯¯¯ )_)