Offipalsta.COM  

Palaa takaisin   Offipalsta.COM > Off-Road > Tekniikka & Jutustelu

Tekniikka & Jutustelu Yleistä keskustelua maastureihin ja/tai off-roadiin liittyen

Vastaus
 
Työkalut Etsi tästä viestiketjusta Näkymä
  #1  
Vanha 27.03.2010, 18:59
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Post

C303 disc brake conversion


Ciao everyone, i have seen in several threads some nice pics of disc brake conversion for the Volvo portal axles...
I am working on these great axles since i got a pair of them.
i don' t like so much drums and mine were in such bad condition that while changing them, the disc option became a must.

I would like to understand something more about it as my ideas are quite confused.

Looking on internet i have found quite immediately http://www.omt-offroad.com/ in germany, for sure a beautifull kit but what a price !!!!!

Arska-tehtaalta suggested me these 2 finnish places:

http://www.offroadtarvike.fi/etusivu/

http://www.offivaruste.com/catalog/index.php

both seems to do disc conversion.

A friend of mine here just machined the wheel hub, made the 6 holes and runs on this way...someone here used 2 extra flanges on the inner and outer side of the reduced hub to have a flat surface where to insert the new scews...i think it' s smart

Another guy i met on another forum machined the hub even smaller and welded a brand new biult 6 holes flange to it.... don' t know if it can become weaker in this way...

This is my first 4x4 and my first serious job! i am pretty sure i couldn' t find anything more complicated to do with my poor knowledge!
I' d just like to adopt the less invasive solution and do it in the best possible way...

I really like to have you opinion!

Ciao have a nice week end!!!

Vastaa lainaten
  #2  
Vanha 27.03.2010, 21:52
pee:n Avatar
pee pee ei ole kirjautuneena
Moderator
 
Rekisteröitynyt: 21.02.04
Sijainti: Mäntsälä P
Viestit: 12.904
Perusasetus

Hello Ravio,

that way to do it, like offroadtarvike or offivaruste is most common and simple + cheap way to get fe. toyota discs suite for C30X axles

those two extra pieces are "hightech" in my eyes, but it doesnt mean that they are bad or useless

I think there is no need to weld any extras, main point is get those surfaces straight against discs, and if you make holes and "worms" for 6 x 139,7 circle, you have many variations for rims

there is some picture from my project, i used toyo discs, wilwood and rover brakecalibers

http://forums.offipalsta.com/showthr...t=37646&page=2

mr. pee
__________________
- Levannon We(l)ho -
Vastaa lainaten
  #3  
Vanha 28.03.2010, 09:25
offroadjouni:n Avatar
offroadjouni offroadjouni ei ole kirjautuneena
Super Moderator
 
Rekisteröitynyt: 10.06.02
Sijainti: Kirkkonummi
Viestit: 6.392
Perusasetus

Here's one topic from our ex-garage -> http://www.fjdc.org/bbs/viewtopic.php?t=373 . The Jeep is using Offivaruste disc brake kit.
Vastaa lainaten
  #4  
Vanha 28.03.2010, 10:46
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

so basically i can have the hubs machined here to the diameter of 173 mm , 6 new holes at a 139.7 mm and place new columns in those ones...do you have a straight hole or with a thread to screw columns in?
by looking at the link in ex garage forum in these 2 pictures it' s clear the process...
Liitetiedostot
Click image for larger version

Name:	img1621273.jpg‎
Views:	774
Size:	55,5 Kt
ID:	11598   Click image for larger version

Name:	img1779328.jpg‎
Views:	2041
Size:	93,6 Kt
ID:	11599  
Vastaa lainaten
  #5  
Vanha 28.03.2010, 10:49
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

...it seems that there is a flange bolt on with the 2 extra screws...

i looked everywhere on offivarusta web site but i could not find any email !!!!!!!!!
do you know if they have one to email them for pricing?

Ciao enjoy your sunday!
Vastaa lainaten
  #6  
Vanha 28.03.2010, 10:55
offroadjouni:n Avatar
offroadjouni offroadjouni ei ole kirjautuneena
Super Moderator
 
Rekisteröitynyt: 10.06.02
Sijainti: Kirkkonummi
Viestit: 6.392
Perusasetus

Lainaus:
Alkuperäinen kirjoittaja ravio Näytä viesti
i looked everywhere on offivarusta web site but i could not find any email !!!!!!!!!
do you know if they have one to email them for pricing?
koopeeoffivaruste.com
Vastaa lainaten
  #7  
Vanha 28.03.2010, 13:59
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

i' ll write them right now thank you!
Vastaa lainaten
  #8  
Vanha 28.03.2010, 14:28
Pauli:n Avatar
Pauli Pauli ei ole kirjautuneena
Moderator
 
Rekisteröitynyt: 06.02.03
Sijainti: Helsinki, Finland.
Viestit: 5.091
Perusasetus

Lainaus:
Alkuperäinen kirjoittaja ravio Näytä viesti
i' ll write them right now thank you!
Put your mobile number to the message, so KooPee can call you.
Vastaa lainaten
  #9  
Vanha 28.03.2010, 15:29
pee:n Avatar
pee pee ei ole kirjautuneena
Moderator
 
Rekisteröitynyt: 21.02.04
Sijainti: Mäntsälä P
Viestit: 12.904
Perusasetus

Lainaus:
do you have a straight hole or with a thread to screw columns in?
by looking at the link in ex garage forum in these 2 pictures it' s clear the process...

6 holes with thread, and hexagon bolts from inside

those 2 smaller holes with threads are for "centering" the disc - and in picture ther is spacer bolted... (not needed there)
__________________
- Levannon We(l)ho -
Vastaa lainaten
  #10  
Vanha 30.03.2010, 15:58
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

thank you!
i ve just received an email back fro offivaruste they say they have a new bolt on kit for a disc conversion on going that will be available in 2 - 3 weeks...i' ll wait to see it before doing anything!
Does anyone of you know anything about it?
Vastaa lainaten
  #11  
Vanha 30.03.2010, 22:37
Pauli:n Avatar
Pauli Pauli ei ole kirjautuneena
Moderator
 
Rekisteröitynyt: 06.02.03
Sijainti: Helsinki, Finland.
Viestit: 5.091
Perusasetus

Lainaus:
Alkuperäinen kirjoittaja ravio Näytä viesti
Does anyone of you know anything about it?
Yes, I know that, but it's a product development, so I will not tell, sorry.
Vastaa lainaten
  #12  
Vanha 31.03.2010, 05:18
Pete:n Avatar
Pete Pete ei ole kirjautuneena
Veteraani+
 
Rekisteröitynyt: 29.03.05
Sijainti: Sipoo, Suomi
Viestit: 1.673
Perusasetus

Lainaus:
Alkuperäinen kirjoittaja Pauli Näytä viesti
Yes, I know that, but it's a product development, so I will not tell, sorry.
This means that Pauli doesn't have a glue what is happening there (he works for offivaruste)
Vastaa lainaten
  #13  
Vanha 31.03.2010, 06:12
pee:n Avatar
pee pee ei ole kirjautuneena
Moderator
 
Rekisteröitynyt: 21.02.04
Sijainti: Mäntsälä P
Viestit: 12.904
Perusasetus

Lainaus:
Alkuperäinen kirjoittaja Pete Näytä viesti
This means that Pauli doesn't have a glue what is happening there (he works for offivaruste)

onks Paulilla liimat loppu

tarkoitaks Pete >clue> ??? Sorry, oli ihan pakko...
__________________
- Levannon We(l)ho -
Vastaa lainaten
  #14  
Vanha 01.04.2010, 20:19
Pete:n Avatar
Pete Pete ei ole kirjautuneena
Veteraani+
 
Rekisteröitynyt: 29.03.05
Sijainti: Sipoo, Suomi
Viestit: 1.673
Perusasetus

Lainaus:
Alkuperäinen kirjoittaja pee Näytä viesti
onks Paulilla liimat loppu

tarkoitaks Pete >clue> ??? Sorry, oli ihan pakko...
Heh
Vastaa lainaten
  #15  
Vanha 02.04.2010, 20:05
liisi:n Avatar
liisi liisi ei ole kirjautuneena
Aktiivijäsen+++
 
Rekisteröitynyt: 23.05.04
Sijainti: Uusimaa, Finland.
Viestit: 441
Perusasetus

Under construction


Lainaus:
Alkuperäinen kirjoittaja ravio Näytä viesti
Does anyone of you know anything about it?
Vastaa lainaten
  #16  
Vanha 12.04.2010, 17:38
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

here i am ! just finished sand blasting and priming every single part of the axles!
i think i' ll wait to see what' s this new product!
thanks pauli i am just curios about it!!!
can you eventually tell me if in the main time i can have the hubs machined and the new holes drilled for my 16 inch wheels? i suppose it's still needed.

i am trying also to calculate which inclination i need to give to the flat part where the leaf spring lies on on the axles looking at the original patrol axles...it seems to me something around 22 23 degrees fron and rear...

did anyone of you make something particular on volvo's to adapt them on the patrol?
Ciao have a nice day!
Vastaa lainaten
  #17  
Vanha 12.04.2010, 20:34
LaaLaa:n Avatar
LaaLaa LaaLaa ei ole kirjautuneena
Legenda
 
Rekisteröitynyt: 10.01.03
Sijainti: Lahti, Finland.
Viestit: 6.184
Perusasetus

Lainaus:
Alkuperäinen kirjoittaja ravio Näytä viesti
have the hubs machined and the new holes drilled for my 16 inch wheels? i suppose it's still needed.
Hi ravio,
I have the 'feeling' that those new under construction disc brakes are supposed to fit regular 15" rims with original volvo bolt pattern
__________________
~~~~~~~~~~~~~~
www.suzuki4x4club.fi
~~~~~~~~~~~~~~
Vastaa lainaten
  #18  
Vanha 12.04.2010, 21:15
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

here some pics of the c303 as i founded it
Liitetiedostot
Click image for larger version

Name:	volvo 3.jpg‎
Views:	394
Size:	51,4 Kt
ID:	11970   Click image for larger version

Name:	volvo 4.jpg‎
Views:	468
Size:	76,4 Kt
ID:	11971   Click image for larger version

Name:	volvo 5.jpg‎
Views:	459
Size:	55,4 Kt
ID:	11972  
Attached Images
File Type: jpg volvo 1.jpg‎ (72,2 Kt, 194 lukua)
File Type: jpg volvo 2.jpg‎ (75,3 Kt, 187 lukua)

Viimeksi muokannut ravio : 12.04.2010 21:18
Vastaa lainaten
  #19  
Vanha 12.04.2010, 21:17
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

another one and all axles dismounted sand blasted and primed.
Liitetiedostot
Click image for larger version

Name:	volvo 6.jpg‎
Views:	472
Size:	50,7 Kt
ID:	11974   Click image for larger version

Name:	IMG00077-20100412-1739.jpg‎
Views:	423
Size:	80,5 Kt
ID:	11975   Click image for larger version

Name:	IMG00078-20100412-1739.jpg‎
Views:	455
Size:	92,6 Kt
ID:	11976   Click image for larger version

Name:	IMG00079-20100412-1739.jpg‎
Views:	390
Size:	80,3 Kt
ID:	11977  
Vastaa lainaten
  #20  
Vanha 12.04.2010, 21:20
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

i did not understand that the previous image was of the new kit...if it' s like this i think i cannot use my new 16 inch rims with standard nissan 6 holes...
Vastaa lainaten
  #21  
Vanha 20.04.2010, 18:45
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

hey guys do you know which toyota model' s discs are used for the conversion?
Vastaa lainaten
  #22  
Vanha 20.04.2010, 19:33
Jeeper:n Avatar
Jeeper Jeeper ei ole kirjautuneena
Sankari
 
Rekisteröitynyt: 14.01.03
Sijainti: PäHäMa/FJDC
Viestit: 4.067
Perusasetus

in this disc brake swap is KZJ rotors: http://forums.offipalsta.com/showthread.php?t=18738
Vastaa lainaten
  #23  
Vanha 20.04.2010, 20:34
Patu925 Patu925 ei ole kirjautuneena
Veteraani+
 
Rekisteröitynyt: 06.09.08
Sijainti: Imatra
Viestit: 1.560
Perusasetus

http://translate.google.fi/translate...%3Dyrityksemme

There is one kind of version...

Viimeksi muokannut Patu925 : 22.04.2010 16:40
Vastaa lainaten
  #24  
Vanha 21.04.2010, 15:05
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

got it, i' ll go for them too...
in this pic from the thread you linked me to, it' s shown the custom built flange for the caliper screwed to the outher 7 bolts diameter of the gear box case, do you think that attaching it to the inner 6 bolts can be possible? i think i saw it somewhere done it in this other way...which solution will be easier?
Liitetiedostot
Click image for larger version

Name:	swamber-kiinnike.jpg‎
Views:	495
Size:	49,6 Kt
ID:	12219  
Vastaa lainaten
  #25  
Vanha 22.04.2010, 16:39
ravio ravio ei ole kirjautuneena
Aloittelija
 
Rekisteröitynyt: 25.03.10
Sijainti: Italia
Viestit: 26
Perusasetus

if i am basically right what i should need to do is to machine my volvo whell hub to a 173 mm diameter, after that have the 6 new holes drilled in a 139,7 mm diameter....

looking on brembo website the drawing with all toyota disc measure, i just checked for my personal curiosity the nissan patrol datas, and i have noticed a couple of differences that caught my attention ( i hearbyt attach the 2 drawings as well as the list of all models using these rotors):

it seems that the nissan bolt pattern is 137 mm diameter???? i think it' s a mistake, did they maybe forget a "9" ?????
nissan holes are for M12 and toyota 14.55.... can i use my whell stud M12 x 1,25 or do i have to get new ones bigger?
At this point i am asking someone driving a toyota: is the wheel the same or does it have a different bolt patter/holes measure???

Thank you again !!!!

By the way checking on internet and asking a dealer here in my country i have found an afyter market rotor for that toyota disk made by DBA disc brake australia, with a slotted face that seems to be more performant! i think i' ll go for that !

ciaooo
Attached Files
File Type: doc dati disco nissan.doc‎ (113,0 Kt, 217 lukua)
File Type: doc dati disco toyota.doc‎ (112,0 Kt, 227 lukua)
Vastaa lainaten
Vastaus


Käyttäjiä lukemassa tätä viestiketjua: 1 (0 jäsentä and 1 vierasta)
 
Työkalut Etsi tästä viestiketjusta
Etsi tästä viestiketjusta:

Tarkennettu haku
Näkymä

Pikalinkit

Samanlaisia viestiketjuja
Viestiketju Aloittaja Foorumi Vastauksia Viimeisin viesti
Myydään C303 KVD:llä Rekisteröimätön O/M/V Ajoneuvot 0 30.04.2009 09:02
Myyty 35/12,5-15 COOPER DISC LT NASTA Ipe64 O/M/V Renkaat ja vanteet 0 17.01.2009 08:12
King Cab Solid Axle Swap Gary Grand Tekniikka & Jutustelu 17 19.01.2005 20:34
Brake noise eliminator nepa Vuosimallit 1984-1996 0 08.08.2002 09:21


Sivu luotu: 13:33 (GMT +2).